Comware

 View Only

switching to 100mb site-site link using routing on 2910al

This thread has been viewed 0 times
  • 1.  switching to 100mb site-site link using routing on 2910al

    Posted Aug 23, 2013 01:12 PM

    All,

     

    Currently have a Pt-to-Pt DS3 connection terminated onto Cisco 3845 routers.

     

    Switching to a 100mb fiber connection and would like to go directly to a Cisco switch at HQ over the 100mb fiber to Remote Office that has two HP2910al switches.

     

    While I know I can just extend a VLAN to the Remote Office I would like to use a route so that I can fall back to a VPN connection over DSL/Cable (outside scope of this post).

     

    I am having two issues, it seems that the Remote1 switch works fine, the Remote2 switch is not reachable (no management or interfaces).

     

    The second issue is that the route just goes away so I am not sure if I have routing setup properly on Remote1.

     

    HQ Cisco switch connection to 100mb fiber looks like:

    -----HQ-----

    interface Vlan159
     ip address 172.19.159.25 255.255.255.248
    !
    ip route 172.19.161.0 255.255.255.0 172.19.159.30
    ip route 172.19.164.0 255.255.255.0 172.19.159.30
    ip route 172.19.165.0 255.255.255.0 172.19.159.30
    -----HQ-----

     

    Remote Office switch 1:

    hostname "remote-hp2910-48-00"
    module 1 type j9147a
    ip dns domain-name "mydomain.com"
    ip dns server-address priority 1 172.30.0.38
    ip route 0.0.0.0 0.0.0.0 172.19.159.25
    ip routing
    interface 1
       speed-duplex 100-full
       exit
    vlan 1
       name "DEFAULT_VLAN"
       no untagged 1-48
       no ip address
       exit
    vlan 159
       name "ROUTING"
       untagged 1-2
       ip address 172.19.159.30 255.255.255.248
       exit
    vlan 161
       name "MGMT"
       tagged 48
       ip address 172.19.161.1 255.255.255.0
       exit
    vlan 164
       name "ANCILLARY"
       untagged 37-44
       tagged 48
       ip address 172.19.164.1 255.255.255.0
       exit
    vlan 165
       name "BUSINESS"
       untagged 3-36
       tagged 48
       ip address 172.19.165.1 255.255.255.0
       ip helper-address 172.30.0.38
       exit
    no autorun
    password manager
    password operator

     

    Remote office switch 2:

    hostname "remote-hp2910-48-02"
    module 1 type j9147a
    ip default-gateway 172.19.159.25
    vlan 1
       name "DEFAULT_VLAN"
       no untagged 1-48
       no ip address
       exit
    vlan 161
       name "MGMT"
       tagged 48
       ip address 172.19.161.2 255.255.255.0
       exit
    vlan 164
       name "ANCILLARY"
       untagged 37-44
       tagged 48
       ip address 172.19.164.2 255.255.255.0
       exit
    vlan 165
       name "BUSINESS"
       untagged 1-36
       tagged 48
       ip address 172.19.165.2 255.255.255.0
       exit
    primary-vlan 161
    management-vlan 161
    no autorun
    password manager
    password operator

     

    Any comments/suggestions would be great.  I am more familiar with Cisco, so I think I am only missing something easy that I am over looking.

     

    Regards,

    -kg